Model /Specification

T-50A

T-50B

T-50C

T-50D

CH1

CH2

CH3

CH1

CH2

CH3

CH1

CH2

CH3

CH1

CH2

CH3

DC output voltage

5V

12V

-5V

5V

12V

-12V

5V

15V

-15V

5V

15V

24V

Output voltage error (Note2)

±2%

±5%

±5%

±2%

±5%

±5%

±2%

±5%

±5%

±2%

±6%

±6%

Rated output current

7A

1A

1A

5A

1A

1A

4A

1A

1A

3A

1A

1A

Output current rage

0.6-7A

0.2-1A

0.2-1A

0.6-5A

0.2-1A

0.2-1A

0.6-4A

0.2-1A

0.2-1A

0.6-4A

0.2-2A

0.2-1A

Wave and noise(Note3)

100mV

100mV

100mV

100mV

100mV

100mV

100mV

100mV

100mV

50mV

120mV

120mV

Inlet stability(Note4)

±0.5%

±0.5%

±0.5

±0.5%

±0.5%

±0.5

±0.5%

±0.5%

±0.5

±0.5%

±1%

±1%

Load stability(Note5)

±1%

±4%

±4%

±1%

±4%

±4%

±1%

±4%

±4%

±1%

±5

±5%

DC output power

52W

49W

50W

51W

Efficiency

66%

69%

71%

72%

Adjustable range for DC voltage

CH1+10,-5%

CH1+10,-5%

CH1+10,-5%

CH1+10,-5%

AC input voltage range

85～132VAC/170～264VAC selected by switch 47～63Hz;240～370VDC

Input current

1.6A/115V 0.8A/230V

AC impulse current

Cold-start current 20A/115V 40A/230V

Leakage current

<0.5A/240VAC

Overload protection

105%～150% Type：PULSING HICCUP SHUTDOWN Reset auto recovery

Over-voltage protection

……

High-temperature protection

Temperature coefficient

±0.03%℃(0～50℃) ON+5V OUTPUT

Setup rise hold up time

200ms,50ms,16ms

Vibration

10～500Hz,2G 3AXES 10min./1cycle,Period for 60min,Each axes

Withstand voltage

Input and output interval：1.5KVAC，Input and enclosure：1.5KVAC，Output and enclosure：0.5KVAC

Isolation resistance

Input and output interval，Input and enclosure，Output and enclosure：500VAC/100M Ohms

Working temperature and humidity

-10℃～+60℃，20%～90%RH

Store temperature and humidity

-20℃～+85℃,10%～95%RH

Overall dimension

159*97*38mm

Weight

0.54Kgs

Safety standards

Meet UL1012 requirement(Not apply for the mark)

EMC standards

……

Note:1.The testing condition for the parameter above is:230VAC input, rated load,25℃ 70%Rh,Humidity
2.Error,include the setting error, line stability and load stability.(Note:5)
3.Wave test:adopting“A12”double wire for 20MHz,and 0.1uF&uF capacitor short-circuit for interrupting
4.Inlet voltage stability test: when is over load, the lowest voltage of inlet is representative to the highest voltage.
5.Load stability test: The load is from 0% to 100%,others 60%.
6.C2、3、11must be knocked down.